Best Welding Magnets and Magnetic Squares (2026)
Welding magnets are the fastest way to hold two pieces of steel at a precise angle for tack welding. No clamping pressure to adjust, no jaws to position, no threads to turn. You set the magnet on the material, bring the second piece into contact, and the magnet holds it at the correct angle while you tack. For 90-degree corners, 45-degree miters, and T-joints, nothing else is as fast.
But not all welding magnets are equal. Cheap magnets lose their holding force after a few months of heat exposure. Poorly designed magnets attract so much spatter and steel dust that they become useless without constant cleaning. And magnets that are too weak let material shift during tacking, producing joints that look square but are actually two degrees off — which compounds into a visible error over a multi-piece assembly.
Quick Comparison: Best Welding Magnets
| Magnet | Type | Angles | Holding Force | Switchable | Price |
|---|---|---|---|---|---|
| Strong Hand Adjust-O Magnet Square (MSA45) | Fixed angle, on/off switch | 45° / 90° | 65 lbs | Yes | $35-50 |
| Magswitch MagSquare 600 | Switchable on/off | 90° / flat / round stock | 607 lbs (max breakaway) | Yes | about $260 |
| Bessey Magnetic Square | Fixed angle | 45° / 90° | 55 lbs | No | $15-25 |
| Hobart Magnetic Welding Squares Set | Fixed angle (multi-size) | 45° / 90° | 25-75 lbs | No | $20-35 (set) |
| Lincoln Electric Magnetic Holders | Fixed angle | 45° / 90° | 40-75 lbs | No | $12-20 each |
How Welding Magnets Work
Welding magnets use permanent magnets — typically ferrite (ceramic) or neodymium (rare earth) — housed in a steel body with machined flat faces set at specific angles. The magnetic field passes through the steel body and into any ferrous material placed against the flat faces, creating a holding force that keeps the material positioned at the magnet’s preset angle.
Ferrite vs. Neodymium Magnets
Ferrite (ceramic) magnets are the traditional choice for welding magnets. They are inexpensive, resist demagnetization from heat reasonably well (Curie temperature around 450C), and produce adequate holding force in larger sizes. Most budget and mid-range welding magnets use ferrite.
Neodymium (rare earth) magnets produce dramatically higher holding force per unit volume. A neodymium welding magnet the size of a matchbox can match the holding force of a ferrite magnet the size of your fist. However, neodymium magnets are more susceptible to heat demagnetization (Curie temperature around 310C for standard grades), which matters in welding applications where the magnet may be close to the arc. High-temperature grades (H, SH, UH, EH) have higher heat tolerance but cost more.
What Reduces Magnet Holding Force
Heat exposure: Placing a magnet directly adjacent to a welding arc or allowing heavy spatter to heat the magnet body reduces holding force temporarily and can cause permanent demagnetization over time. Keep magnets at least 2-3 inches from the weld zone.
Surface contamination: Steel dust, grinding particles, and spatter on the magnet faces create air gaps that reduce effective holding force. Clean magnet faces before each use.
Material thickness: A magnet rated for 75 pounds of holding force on 1/4-inch plate will hold less force on thin sheet metal because the magnetic circuit is less efficient through thinner material.
Surface condition: Mill scale, rust, and paint on the workpiece surface reduce magnetic contact. Clean, bare steel provides the strongest magnetic hold.
Detailed Reviews
Strong Hand Tools Adjust-O Magnet Square (MSA45) — Best Everyday Magnetic Square
Get Strong Hand Adjust O MagnetThe Adjust-O Magnet Square is an arrow-style square for 45- and 90-degree setups. Unlike most arrow magnets, it has an on/off switch. Strong Hand gives the switch off, mid-point and on positions, so you can place the square and slide parts into line with the magnet off or partly engaged, then switch it fully on for the tack. The magnet no longer snaps onto parts before they are aligned, and the square lifts off heavy stock without prying.
Strong Hand rates the MSA45 at 65 lb of pull, measured on the longest side against 3/8-inch steel. The body is 4.4 x 3.8 x 1 inches and weighs 1.0 lb. The larger MSA47 is rated at 75 lb. The maker lists rare earth magnets and a fully enclosed body for easier cleaning, and says the square suits round and square tubing, angle and flat stock. This is a fixed-angle tool. For any angle from 30 to 275 degrees in one tool, Strong Hand makes the Adjust-O Angle Magnet Positioner (MAV120), at a much higher price.
What stands out:
- On/off switch with a mid-point position for controlled setup
- 65 lb maker rating on 3/8-inch steel from a 1 lb body
- Rare earth magnets in a fully enclosed body
- 45- and 90-degree faces cover the most common joints
Limitations:
- Fixed 45 and 90 degrees only; no adjustable angle
- 65 lb is enough to position parts, not to hold heavy plate
- The rating assumes 3/8-inch steel; thinner sheet holds less
- Costs more than plain arrow magnets of similar size
Magswitch 600 — Strongest Holding Force
Get Magswitch 600The Magswitch 600 is a fundamentally different type of welding magnet. Instead of a permanent magnet that is always on, the Magswitch uses a rotating magnetic element that you activate and deactivate with a twist of the switch handle. When switched on, it engages with up to 600 pounds of holding force. When switched off, the magnetic field is directed internally and the device releases from the workpiece cleanly with near-zero residual magnetism.
This switchable design solves the two biggest frustrations with conventional welding magnets. First, conventional magnets are difficult to remove from heavy steel — you have to slide them off an edge, which is not always possible mid-assembly. The Magswitch releases instantly. Second, conventional magnets collect steel chips and spatter continuously because they are always magnetized. The Magswitch stays clean when switched off.
The 600-pound rating refers to the maximum breakaway force on thick, clean steel plate. Real-world holding force on typical fabrication material is lower — expect 200-400 pounds on 1/4-inch plate, which is still substantially more than any conventional welding magnet. This is enough to hold heavy angle iron, channel, and plate for tacking without additional support.
The Magswitch 600 only holds material flat or at 90 degrees — it does not offer the angle versatility of the Adjust-O or the multi-angle capability of conventional arrow magnets. It is a brute-force holding tool, not an angle-setting tool.
What stands out:
- Switchable on/off — engages and releases instantly with a twist
- Up to 600 pounds holding force — the strongest magnet in this roundup by a wide margin
- Near-zero residual magnetism when switched off — stays clean and releases cleanly
- Holds heavy material that conventional magnets cannot support
- Eliminates the struggle of removing strong magnets from workpieces
- Durable construction designed for heavy industrial fabrication
Limitations:
- Only holds flat or 90-degree configurations — no multi-angle capability
- Significantly more expensive than conventional welding magnets
- The 600-pound rating is only achieved on thick, clean steel — real-world holding force is lower
- Heavier and bulkier than conventional magnetic squares
- The switching mechanism can become stiff if spatter enters the rotating element
- Not a replacement for multi-angle magnets — it serves a different function
Bessey Magnetic Square — Best Fixed-Angle Value
Get Bessey Magnetic SquareThe Bessey magnetic square is a classic arrow-style welding magnet executed to German manufacturing standards. The arrow shape provides 45-degree and 90-degree holding positions, which covers the two angles used in the vast majority of fabrication work. The 55-pound holding force is adequate for positioning and tacking material up to approximately 3/16-inch plate.
What separates the Bessey from generic arrow magnets is the machining quality. The flat faces are ground to consistent flatness, which means the workpiece sits flush against the magnet with full contact across the surface. Cheap magnets often have uneven faces that create point-contact holds, reducing effective holding force and allowing the workpiece to rock or pivot slightly during tacking.
The steel body uses a powder-coat finish that provides some spatter resistance, though not at the level of chrome or copper plating. The ferrite magnets inside are robust enough to maintain their rated force through normal welding temperature exposure when the magnet is kept a few inches from the arc.
At the price point, the Bessey delivers the best combination of holding force accuracy and build quality available in a fixed-angle welding magnet. It is the arrow magnet to buy if you want reliable performance without the premium pricing of specialty brands.
What stands out:
- Precisely ground flat faces provide full-surface material contact
- 55-pound holding force is strong for a standard arrow magnet
- 45-degree and 90-degree positions cover the most common fabrication angles
- German manufacturing quality — consistent machining and magnetic strength
- Powder-coat finish provides basic spatter resistance
- Competitive pricing for the quality level delivered
Limitations:
- Only 45 and 90-degree angles — no adjustability
- 55-pound force is insufficient for heavy plate and structural steel
- Powder coat is less spatter-resistant than chrome or copper plating
- Ferrite magnets are bulkier than neodymium for equivalent holding force
- No V-groove for tube and pipe centering
- Will need supplemental clamping for material heavier than 3/16-inch
Hobart Magnetic Welding Squares Set — Best Starter Set
Get Hobart Magnetic Welding Squares SetHobart packages multiple magnetic squares in different sizes, giving you a starter set that handles both small and large workpieces from one purchase. The set typically includes a small arrow magnet (25 lbs), a medium (50 lbs), and a large (75 lbs), providing appropriate holding force for different material sizes without a single oversized magnet that is awkward on small parts.
Having multiple sizes on hand is more useful than it initially seems. A 75-pound magnet on 20-gauge sheet metal is cumbersome and actually makes positioning harder because the strong magnetic field pulls the thin material before you can align it properly. A 25-pound magnet handles sheet metal cleanly while the 75-pound magnet handles 1/4-inch plate — each size has its appropriate range.
The individual magnet quality is good for the price. Faces are reasonably flat, holding force matches the ratings within typical tolerances, and the ferrite magnets retain their strength through normal use. The paint finish attracts spatter over time, but a wire brush cleaning restores the faces quickly.
What stands out:
- Multiple sizes in one package covers a range of material thicknesses
- Size-appropriate magnets prevent handling issues with thin material
- Good holding force accuracy relative to stated ratings
- 45-degree and 90-degree positions on all sizes
- Affordable entry into welding magnets for a new shop
- Hobart quality is reliable for the price point
Limitations:
- Individual magnet quality is below Bessey and Strong Hand levels
- Paint finish is less spatter-resistant than powder coat or plating
- No V-grooves, no adjustable angles, no switchable operation
- The smallest magnet in the set has limited utility beyond very thin material
- Face flatness can vary between individual units in a set
- You may outgrow the set quickly if you do serious fabrication work
Fireball Tool Dragon Puck — Best Multi-Function Design
Get Fireball Tool Dragon PuckThe Fireball Tool Dragon Puck is an unconventional welding magnet that has earned a passionate following in the fabrication community. Instead of the standard arrow shape, the Dragon Puck is a cylindrical puck with machined flats, V-grooves, and step features that enable holding configurations no standard arrow magnet can achieve.
The flat faces hold material at 90 degrees like a conventional square, but the stepped edge allows you to set the magnet flush with a material edge while holding a second piece at 90 degrees — creating an offset T-joint position that arrow magnets cannot replicate. The V-groove on one face centers tube and pipe, and the magnetic strength (approximately 100 lbs) is strong enough to hold most tubing and light structural shapes securely.
The Dragon Puck excels on welding tables with hole patterns. The puck’s diameter is designed to sit inside or against standard table fixture holes, turning the puck into a magnetic stop, reference surface, or holding point. This integration with modular welding tables is where the design really shows its value.
The neodymium magnet assembly provides strong holding force relative to the compact size. The machined steel body is precision-ground on all functional surfaces, and the build quality is noticeably higher than mass-produced arrow magnets.
What stands out:
- Multi-function design enables holding configurations impossible with arrow magnets
- Stepped edge creates offset positions for T-joints and edge-flush setups
- V-groove centers tube and pipe securely
- Integrates with modular welding table hole patterns
- 100-pound holding force from a compact neodymium assembly
- Precision-machined surfaces exceed the flatness of standard arrow magnets
Limitations:
- Less intuitive to use than simple arrow magnets — requires learning the holding positions
- No preset 45-degree position — the puck is primarily a 90-degree and flat holder
- Premium price for a single magnet unit
- The cylindrical shape can roll on non-flat surfaces if not seated against a workpiece
- Limited availability — primarily sold direct from Fireball Tool
- The cult following has created occasional supply constraints
Lincoln Electric Magnetic Holders — Best Budget Option
Get Lincoln Electric Magnetic HoldersLincoln Electric’s magnetic holders are straightforward arrow-style welding magnets at a price point that makes buying several at once easy on the budget. Available in multiple sizes with holding forces from 40 to 75 pounds, they provide basic 45-degree and 90-degree positioning capability without any premium features.
The build quality is consistent with Lincoln’s accessories line — functional, durable, and adequately manufactured. The faces are reasonably flat, the magnetic strength meets the ratings, and the steel body withstands normal shop use without visible degradation. The red enamel finish is not the most spatter-resistant coating, but it is easily cleaned.
The value proposition is simple: if you need six or eight arrow magnets to hold a complex assembly during tacking, Lincoln’s price point lets you buy the quantity you need without the per-unit cost of premium brands. You may replace them more frequently than Bessey or Strong Hand magnets, but the lower acquisition cost makes that acceptable for most shops.
What stands out:
- Lowest per-unit cost of any brand-name welding magnet
- Available in multiple sizes for different material thickness ranges
- Adequate holding force and angle accuracy for standard fabrication
- Lincoln Electric brand — widely available at every welding supplier
- Durable enough for regular shop use
- Buy in quantity without significant budget impact
Limitations:
- Face flatness and magnetic consistency vary more than premium brands
- Enamel paint finish collects spatter and chips over time
- Ferrite magnets are bulkier than neodymium alternatives
- No advanced features — no V-grooves, no adjustable angles, no switching
- The 40-pound small size is marginal for anything beyond light sheet metal
- You get what you pay for — functional but unremarkable
How to Use Welding Magnets Effectively
Keep Magnets Away from the Arc
Welding magnets lose holding force when overheated. Position the magnet at least 2-3 inches from where you are welding. If the magnet body becomes too hot to touch with bare hands, it has been too close to the arc and may have experienced some demagnetization.
Clean Magnet Faces Before Every Use
A thin layer of steel dust on the magnet face can reduce effective holding force by 20% or more. A quick wipe with a shop rag, or a pass with a wire brush for stubborn buildup, maintains full holding force. Switchable magnets like the Magswitch can be cleaned while de-energized, making the process easier.
Use Magnets for Positioning, Not Final Holding
Magnets excel at setting angles and positions for tack welding. For final welding passes where thermal stress can move material, add mechanical clamps to maintain joint alignment. Think of magnets as your setup tool and clamps as your holding tool.
Pair the Right Size Magnet to Your Material
Oversized magnets on thin material make positioning harder because the magnetic field pulls the workpiece before you can align it. Undersized magnets on heavy material let the workpiece shift during tacking. Match your magnet size to your material weight for best results.
Choosing a Magnetic Welding Square: Fixed, Switchable or Adjustable
There are three kinds of magnetic welding square. A fixed arrow square holds 45 and 90 degrees and is always on. A switchable square has a mechanical on/off, so you can place it, slide it and lift it off without fighting the magnet. An adjustable positioner locks any angle across a wide range. Paying more gets you switching first, then more holding force, then more angles.
None of these picks were tested. The choice rests on each maker’s published pull rating, switching and angle range. For a home or small shop building frames, carts and brackets from tube and angle, buy the Strong Hand Adjust-O Magnet Square (MSA45). Strong Hand rates it at 65 lb on 3/8-inch steel. Its off, mid-point and on switch lets you fit parts before the magnet grabs them. Buy two to four, not one.
Get Strong Hand Adjust-O Magnet Square MSA45Who should skip it: anyone setting up heavy plate or channel. For that work, get the Magswitch MagSquare 600. Magswitch rates it at 607 lb maximum breakaway and lists it at about $260. If you regularly weld 30, 60 or 120 degree joints, look at Strong Hand’s Adjust-O Angle Magnet Positioner (MAV120). Strong Hand lists it as adjustable from 30 to 275 degrees, with two on/off switches, V-groove faces, a 110 lb pull rating and a regular price of $352. That price only pays off if odd angles are routine.
Get Magswitch MagSquare 600 Get Strong Hand Adjust-O Angle Magnet Positioner MAV120Not worth the money: unbranded multipacks of arrow magnets that print a pull number without saying what steel thickness or which face it was measured on. You can’t compare that number with anything.
What a Welding Magnet’s Pull Rating Means
A pull rating is a breakaway figure: the force it takes to pull the magnet straight off clean, flat steel thick enough to carry its whole field. Makers state their test conditions differently:
| Model | Maker’s rating | Stated condition |
|---|---|---|
| Strong Hand Adjust-O MSA45 | 65 lb | Longest side, 3/8-inch steel |
| Strong Hand MAV120 | 110 lb | Maximum pull force |
| Magswitch MagSquare 600 | 607 lb max breakaway | 3/8-inch full saturation thickness; 61 lb 2:1 shear working load |
The shear figure is the one to plan around. Parts on a magnet square usually fail by sliding along the face, not by lifting straight off. For that direction, Magswitch gives a working load of 61 lb, about a tenth of its breakaway number. On steel thinner than the stated 3/8 inch, holding force drops further. Thin sheet holds much less than the label figure, which is why every square here is for positioning and tacking, not for holding parts through the final weld.
Who Makes Welding Magnets
Three makers sell clearly different classes of welding magnet:
- Strong Hand Tools makes fixed Adjust-O squares with on/off switches (MSA45 at 65 lb, MSA47 at 75 lb, per the maker), heavy-duty HD versions with a double plate, the MAV120 adjustable positioner, and Inside/Outside angle magnets. The MLA450 is listed as adjustable from 30 to 270 degrees with 26 lb of pull.
- Magswitch makes switchable permanent magnets. Its MagSquare line is switched mechanically and needs no batteries or power.
- Bessey sells ferrite welder’s set-up squares. The listings show them holding 45, 90 and 135 degrees, and they can be linked together to form other angles.
Buy from a maker that publishes the pull force, test thickness and dimensions for the exact model. Skip any listing that gives none of the three.
Weldable Magnets: Building Magnets Into Jigs and Fixtures
Don’t weld directly to a permanent magnet. Heat weakens both ferrite and neodymium well below their Curie temperatures, and standard N-grade neodymium is generally rated for a maximum working temperature of about 80°C (176°F). A weld bead next to the magnet goes far past that. A weldable magnet is really a steel holder: the holder takes the weld, and the magnet goes in after it cools.
Two builds work:
- Cup (pot) mounting magnets: a neodymium disc set in a steel cup, sold with a countersunk hole or a threaded stud. Weld a nut or tapped tab to the jig, let it cool, then bolt the magnet on. The cup concentrates the field at the face and protects the brittle magnet from knocks.
- Welded pocket and epoxy: weld a mild-steel pocket to the jig, let it cool, then glue the magnet in with epoxy. It’s cheaper, but you can’t replace the magnet without grinding it out.
If the fixture has to release parts quickly, buy a switchable magnet instead. A cup magnet never turns off, so every part has to be slid or levered off it.
Frequently Asked Questions
Do welding magnets affect arc behavior?
Strong magnets near the weld zone can cause arc blow — the magnetic field deflects the welding arc from its intended path. This is most noticeable with DC stick welding at low amperages. Keeping magnets 3+ inches from the arc eliminates the effect in most situations. If you experience arc blow, reposition the magnet or switch to AC welding if the procedure allows.
Can welding magnets hold stainless steel?
Only austenitic stainless steel (304, 316) that is slightly magnetic — most austenitic stainless has very low magnetic permeability and magnets hold poorly or not at all. Ferritic stainless (409, 430) and martensitic stainless (410, 420) are magnetic and work well with welding magnets. When working with non-magnetic stainless, use mechanical clamps or tack welding fixtures instead.
How long do welding magnets last?
A quality ferrite welding magnet that is not repeatedly overheated will maintain most of its holding force for years to decades. Neodymium magnets are more susceptible to heat-induced demagnetization but will also last years with proper use. The most common failure mode is not magnetic degradation — it is spatter buildup and mechanical damage to the flat faces from being dropped.
Should I demagnetize my workpiece after using welding magnets?
Residual magnetism in a workpiece can cause arc blow during welding and attract steel dust after fabrication. For critical work, pass a demagnetizer over the contact area after removing the magnet. For non-critical fabrication, residual magnetism typically does not cause problems and dissipates gradually over time.
Are neodymium welding magnets worth the extra cost?
For most fabricators, yes. Neodymium magnets provide significantly more holding force per unit size, which means you can use a smaller, more maneuverable magnet that still holds your material securely. The compact size also makes placement in tight joint configurations easier. The only caveat is heat sensitivity — keep neodymium magnets further from the arc than you would keep ferrite magnets.
How many welding magnets do I need?
A practical starting set is four medium-sized arrow magnets (50-75 lb) for corner and T-joint setups. Add a pair of small magnets (25-30 lb) for sheet metal, and one or two specialty magnets (an adjustable-angle positioner such as the Strong Hand MAV120, or a switchable square such as the Magswitch MagSquare 600) for unusual angles and heavy material. Most fabricators accumulate 8-12 magnets over time as project needs dictate.
Related Articles
- Best Welding Clamps — mechanical clamping for final holding force after magnetic positioning
- Best Welding Magnets and Clamps — combined guide to fixturing with both magnets and clamps
- Best Welding Tables — modular tables that integrate with magnetic fixtures
- Home Welding Shop Setup — complete workspace planning including fixturing